1-10V PUSH LED Dimmer Driver 25W 350mA to 700mA , Short Cir
- Min. Order:
- 1
- Min. Order:
- 1
- Delivery Time:
- 30 Days
Your message must be between 20 to 2000 characters
Contact Now| Place of Origin: | China |
|---|
1 x 30W PUSH 1-10V Dimmable LED Driver Multi Output Current 350mA - 700mA
Description:
1, Adopt 2pcs DIP switches to supply multi-output current 350mA, 500mA and 700mA. Different current setting can be used for different LED lights, no need to keep stocks for several types of led divers in
your warehouse!
2, PUSH dimming and 1-10V dimming function are available. Dimming mode can be switched easily by
a jumper.
3, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.
4, Memory function: The driver has built-in permanent memory against power failure. Lights can return
to previous dimming level when switch off and on again, even at mains restores.
5, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
6, Maximum length of the cable, from switch to last driver is 20m.
7, Factory setting: 100% dimming level and 250mA output.
8, Reset the LED diver easily by a jumper.
9, Press-in terminals in primary and secondary side, easy assembly.
10, Protection: Short circuit / Over voltage / Over temperature.
11, Long life span 50,000h, 5 years guaranty.
Applications:
For LED down light, LED panel light, led strip, led tube etc…
Dimming Operation:
A) PUSH Dim
Short push (<0.1sec): Ignore, to avoid reaction on AC spike.
Short push (0.1~1sec): Switch on or switch off.
Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.
B) 1-10V Dim
Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.
Synchronization:
For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:
A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.
B) Do a long push, the system will be resynchronized.
Specifications
|
OUTPUT
|
Output current and load |
350mA 16-60V DC 21W max 500mA 16-58V DC 29W max 700mA 16-43V DC 30W max |
|
Output load range |
25W max |
|
|
Current accuracy |
±5% |
|
|
Dimming mode |
1-10V, PUSH |
|
|
INPUT
|
Input voltage |
220-240Vac |
|
Input frequency |
50-60Hz |
|
|
Input current |
0.16A max |
|
|
Power factor |
≥0.90 |
|
|
Efficiency(Note1) |
≥87% |
|
|
Leakage current |
＜0.5mA/240Vac |
|
|
ENVIRONMENT
|
Working temp.(Ta) |
-20~50℃ |
|
Surface temp.(Tc) |
85℃max |
|
|
Working humidity |
20~90%RH non-condensing |
|
|
Storage temp. |
-40~80℃ |
|
|
Life time |
≥50,000hours |
|
|
PROTECTION
|
Isolation class |
Class II, SELV |
|
Protection class |
IP20 |
|
|
Short circuit |
Protection type; auto rest |
|
|
Over voltage |
Protection type; auto rest |
|
|
Over temperature |
Protection type; auto rest |
|
|
SAFETY&EMC
|
Safety |
EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6 |
|
EMC |
EN55015, EN61000-3-2ClassC |
|
|
EN61000-3-3, EN61547 |
||
|
Approvals |
SEMKO, CE |
|
|
Withstand voltage |
IN-OUT:3.75KVAC/5mA/1min; IN-FG:1500VAC/5mA/1min |
|
|
OUT-FG:500VAC/5mA/1min |
||
|
NOTE |
1, Efficiency is measured at 550mA/55Vdc output set by DIP switch 2, All parameters not specially mentioned are measured at 230Vac input, rated load and 25℃of ambient temp. |
|
