Dimmable 1-10V 350mA - 900mA LED Driver 40W With Memory Fu
- Min. Order:
- 1
- Min. Order:
- 1
- Delivery Time:
- 30 Days
Your message must be between 20 to 2000 characters
Contact Now| Place of Origin: | China |
|---|
1-10V Push 40W 350mA - 900mA Dimmable LED Driver for LED panel light
Description:
1, Press-in terminals in primary and secondary side, easy assembly.
2, Long life span 50,000h, 5 years guaranty.
3, with 1-10V and push in PRI and SEC side.
4, no flickering from 0%-100% dimming level
5,The output currents from 350mA to 900mA. It can be set by DIP swiches.
6, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.
7, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.
8 Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
9, Maximum length of the cable, from switch to last driver is 20m.
10, Factory setting: 100% dimming level and 350mA output.
11, Reset the LED diver easily by a jumper.
12, Protection: Short circuit / Over voltage / Over temperature.
Dimming Operation:
A) PUSH Dim
Primary and secondary dimming with PUSH button. It has dimming level memory at main rstore. And the push dim is alway prior.
B) 1-10V Dim
Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.
Synchronization:
For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:
A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.
B) Do a long push, the system will be resynchronized.
Specifications
|
INPUT
|
Input voltage |
220-240Vac |
|
Input frequency |
50-60Hz |
|
|
Input current |
0.20A max |
|
|
Power factor |
≥0.90 |
|
|
Efficiency(Note1) |
≥86% |
|
|
Leakage current |
＜0.5mA/240Vac |
|
|
OUTPUT
|
Output current/voltage and load |
350mA 16-60V DC 21W max 500mA 16-60V DC 30W max 700mA 16-58V DC 41W max 900mA 16-56V DC 50W max |
|
Output load range |
1x50W max |
|
|
Current accuracy |
±5% |
|
|
Dimming mode |
1-10V, PUSH |
|
|
ENVIRONMENT
|
Working temp.(Ta) |
-20~50℃ |
|
Surface temp.(Tc) |
85℃max |
|
|
Working humidity |
20~90%RH non-condensing |
|
|
Storage temp. |
-40~80℃ |
|
|
Life time |
≥50000hours |
|
|
PROTECTION
|
Isolation class |
Class I, SELV |
|
Protection class |
IP20 |
|
|
Short circuit |
Protection type; auto rest |
|
|
Over voltage |
Protection type; auto rest |
|
|
Over temperature |
Protection type; auto rest |
|
|
SAFETY&EMC
|
Safety |
EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6 |
|
EMC |
EN55015, EN61000-3-2ClassC |
|
|
EN61000-3-3, EN61547 |
||
|
Approvals |
SEMKO, CE |
|
|
Withstand voltage |
IN-OUT:3.75KVAC/5mA/1min; IN-FG:1500VAC/5mA/1min |
|
|
OUT-FG:500VAC/5mA/1min |
||
|
NOTE |
1, Efficiency is measured at 1050mA/48Vdc output set by DIP switch 2, All parameters not specially mentioned are measured at 230Vac input, rated load and 25℃of ambient temp. |
|
Applications:
For LED panel light, LED down light, led strip, led tube etc…
