Wireless Red Flash Light Siren Hidden Alarm Siren, Flashing Warning Strobe Siren

Wireless red flash light siren hidden alarm siren 

Wireless Strobe Siren can be used either as a local alarm panel or as the wireless siren for some of our alarm panels. Put the siren switch to SIREN, it would work as a wireless siren, while put the switch to PANEL, it would function as a local alarm system panel.  

 1.Parameter:  

• the external power current should be below 15v and above 8v.
• 4 remote, 8 wireless detector and one wired detector at most to work
• several NC wired detector can be connected in series as one wired connection
• when power on, the green LED flashing times means the numbers of the register remote, and the red LED flashing times means the numbers of registered wireless detectors
• the siren comes with 9v backup battery, able to standby 24 hours when power fails.

 2.How to use as a wireless siren  

• Plug off the power adaptor, Put the siren back switch to SIREN, then plug the adaptor after 2 seconds
•  For 5800/2300/sn5700 alarm system: put the back switch 26/23 to 23
• Press the SENSOR key of the siren, the LED B flashes, press the corresponding transmitting key of the panel, (e.g. 9 for sn5800/5900, * for 2300) the alarm panel would transmit wireless code. The wireless siren's LED would off after receiving the code. You can press the panel transmitting key for several times, every time panel gets it would make a beep, that means the code is correct. At last, Press SENSOR key to store this code and exit registering status. 
•  When the alarm system alarms, the wireless siren would sound, and when the panel stops, it would also stop.

 3.  How to use as a local alarm panel   

1. Plug off the power adaptor, put the siren back switch to PANEL; after 2 seconds, plug in adaptor
2. Key fob registration: press the REMOTE key, and the LEDA flashes. Press a random key on the key fob to make it transmit a code. The siren would sound once after receiving the code. Press the same key of key fob for a few times more, the siren sound a beep every time. That means that is the correct code. Press REMOTE key to save it and exit registering status.
3. Wireless detector registration: press the SENSOR key, and the LED B flashes. Trigger the wireless sensor to make it transmit a code. The siren would sound once after receiving the code. Trigger the wireless detector a few times more, the siren sound a beep every time. That means that is the correct code. Press SENSOR key to save it and exit registering status.
4. Press the arm key of the key fob, the power LED flashes slowly after 2 sounds di di. That means it is already armed. Press the disarm key of the key fob. The red LED is on after a di sound and the panel is disarmed. Trigger the senor when the siren is armed status, the siren would sound for 72 seconds.
5. The siren can work with one wired detectors also. The wired detector should be NC. Connect wired detector's signal wire to + and – of plug cord . When the detector is open circuit, the red LED ON means panel disarmed, and red LED flashing means armed. When the detector is closed circuit, the green LED on means panel disarmed, and green LED flashing means armed.
6. Registering the wired detector: press the SENSOR key, the LED B flashes rapidly. Trigger the wired detector once(closed circuit first then open circuit) LED A is steadily on, at last press SENSOR key to store it. Arm the siren by remote. Trigger the wired detector, it alarms.

 4 . Return to factory default setting: 

Power off, press SENSOR or REMOTE key and hold it, then switch power on. After 3 seconds. Both the red and green led are on. You can release the SENSOR or REMOTE key. At this time, you can press any remote key, the panel has no reponse, that means, the panel is returned to factory default setting.
   

Contact details: 

Soan Electronic Technology Co., Ltd

Contact: Susan Lin